Fire Protection System (FPS) is an authorised Apollo distributor in Bhopal, supplying the bases that Apollo detectors plug into: XPERT 7 and XPERT 8 bases for addressable systems, isolating and intrinsically safe bases, and Series 65, Orbis and AlarmSense bases for conventional systems, including relay and diode versions. Choosing the right base decides how the detector is addressed, isolated, locked and wired.
A universal detector base that fits all Apollo detectors in the Soteria, Discovery and XP95 ranges. It supports isolated and non-isolated devices and has a wide interior for easy access to cables and terminals.
A white flame-retardant polycarbonate mounting box for flush fitting Soteria Dimension detectors into a ceiling opening. It is held in place by self-aligning fixing tabs.
A low insertion force detector base with stainless steel contacts for quick installation, suited to the XP95 and Discovery detector ranges. It is available in white and in black.
An XPERT 7 base with a built-in isolator that senses short circuit faults on Discovery loops and spurs and keeps the disruption they cause to a minimum.
A dedicated white polycarbonate base designed to accept only the Apollo Isolator 55000-720.
An XPERT 7 base for intrinsically safe systems that accepts only I.S. products, so a standard detector cannot be fitted by mistake.
The standard base for Series 65 conventional detectors, designed so detectors fit without force, which helps on suspended ceilings. Detectors fit one way only and can be locked with a grub screw using a 1.5 mm hexagonal screwdriver.
A Series 65 base for conventional systems that have manual call points and detector bases on the same circuit. A Schottky diode on the L1 IN and L1 OUT terminals keeps the circuit working if a detector is removed without permission; it is used with compatible control equipment.
A Series 65 base with one set of volt-free changeover (form C) contacts that change state when the detector signals an alarm, so the detector can switch other equipment.
The Orbis conventional detector base, designed to give installers an open working area with fixing holes shaped for fast mounting.
An Orbis TimeSaver base with a single-pole volt-free changeover contact for switching external equipment. The relay energises when the detector goes into alarm and stays in that state until the detector is reset.
The base for AlarmSense detectors, which can only be mounted on it, used where the detector does not need an integral sounder or sounder visual indicator. It reports a fault if a detector head is removed.
Match the base to the detector range first. The XPERT 8 Base is a universal base for Apollo Soteria, Discovery and XP95 detectors, while the XPERT 7 Base, in white or black, suits the XP95 and Discovery ranges. Both use XPERT addressing: the detector's loop address is set by a coded XPERT card held in the base, and Apollo supplies the cards with its XPERT 7 bases. Soteria Dimension detectors are flush mounted in their own Soteria Dimension mounting box.
Decide whether the base must isolate. An isolator senses a short circuit in the loop wiring and cuts off only the small section around it, so the rest of the loop keeps working. The XPERT 7 Isolating Base does this on Discovery loops and spurs, with up to 20 detectors or their equivalent load allowed between isolating bases. The XPERT 8 Base supports isolated and non-isolated devices and keeps the loop connected while a device is briefly removed. The separate Isolator Base accepts only the Apollo Isolator 55000-720.
For conventional Series 65 systems, choose the standard base, the Diode base (a Schottky diode on the L1 IN and L1 OUT terminals so call points and detectors can share one circuit and it keeps working if a detector is removed), or the Relay base with one set of volt-free changeover contacts that switch on alarm. The Orbis TimeSaver bases have grouped terminals, two fixing centres and a cable stripping guide, and the relay version switches up to 30 V at 1 A. AlarmSense detectors fit only the AlarmSense Base.
For hazardous areas, the XPERT 7 I.S. Base accepts only intrinsically safe detectors, so a standard detector cannot be fitted into an I.S. system by mistake. Intrinsically safe equipment limits electrical energy so that it cannot ignite an explosive atmosphere. FPS supplies and fits the correct base for each Apollo detector in Bhopal and across Madhya Pradesh.
Try "landing valve", "Apollo call point", "9 kg ABC" or a model code.
No products yet. Tap "Add to quote" on any product, then send the whole list to us in one WhatsApp message.
