Fire Protection System (FPS) is an authorised distributor for Kanex fire suppression systems in Bhopal and across Madhya Pradesh, covering tube-actuated panel and machine systems, CO2 systems, clean agent total flooding and kitchen hood systems. We size the system, install it, and return for testing, refilling and service.
Sizes: 2, 4, 6 kg
Pre-engineered clean agent system for electrical cabinets, server racks and wind turbine alternator zones, where the UL listed detection tube both senses the fire and delivers the agent at the source. Available in 2, 4 and 6 kg cylinders with FE-36 (HFC-236fa), FK-5-1-12 or FM-200 (HFC-227ea).
Sizes: 2, 4, 6 kg
Indirect clean agent system for CNC and EDM machines, dry type transformers, DG sets, fume hoods and wind turbines: the red detection tubing only senses the fire and large nozzles then flood the work zone with clean agent. Offered in 2, 4 and 6 kg cylinders.
CO2 based direct system for electrical cabinets, transformers, DG sets and fume hoods, with detection tubing routed around the critical components for 360 degree detection and discharge at the source. Cylinder sizes 4.5 and 6.5 kg subject to design calculation.
Sizes: 4.5, 6.5, 9, 22.5, 45 kg
Indirect high pressure CO2 systems for panels, dry type transformers and generators, CNC and EDM machines and fume hoods, where the detection tube senses the fire and nozzles deliver CO2 as a gentle mist. Cylinder sizes from 4.5 kg up to 45 kg depending on the enclosure.
Pre-engineered direct release system using Novec 1230 clean agent for the electrical compartment of a wind turbine, also suitable for cable runs and trays. Cylinders are offered as 2 and 5 kg (CE) or 2.5, 5 and 10 lbs (DOT).
Indirect release Novec 1230 system recommended for wind turbine electrical compartments, where the tubing detects the fire and large nozzles flood the zone with clean agent. Cylinders in 2 and 5 kg (CE) or 2.5, 5 and 10 lbs (DOT).
Engineered total flooding systems that fill a room with FM-200 (HFC-227ea) or Novec 1230 to put out a fire without wetting or contaminating equipment. Designed for server rooms, data centres and other areas where water would cause as much loss as the fire.
An electrically actuated room system in which smoke detectors signal a fire alarm panel, which opens the control valve and releases the extinguishing media into the affected area. The panel also drives a hooter and can send SMS alerts and calls.
Sizes: 9 L
A wet chemical system for commercial kitchen hoods and cooking lines, using a continuous pneumatic sensor tube fitted inside the extractor hood above the cooking area. The tube bursts at 175 degrees C and floods the cooking zone with Class F agent.
Direct release systems in which the heat and flame sensitive Firetrace detection tubing serves as both the detector and the agent delivery line. Used for small enclosures where suppression is needed right at the source.
Indirect release systems where the Firetrace detection tubing only detects the fire and activates the system, and the agent is discharged through separate nozzles. Recommended for larger machine enclosures.
The range of extinguishing media used with Kanex suppression hardware, covering dry chemical powders, clean agents and carbon dioxide. The right agent depends on the hazard and the equipment being protected.
Start with the hazard, not the cylinder. A single panel, machine or rack is normally protected by a pre-engineered tube system, where a pressurised plastic detection tube runs past the hot spots and bursts at the point nearest the fire. A whole room is protected by a total flooding system that fills the volume with clean agent to the design concentration.
Then pick direct or indirect release. In a direct system the same tube that detects the fire also delivers the agent through the burst hole, which suits small sealed enclosures such as panels and racks. In an indirect system the tube only senses heat and a valve then discharges through separate nozzles, which suits larger or ventilated spaces such as CNC machines, fume hoods, dry transformers and DG sets.
Choose the agent next. Clean agents such as FM-200 (HFC-227ea), FE-36 (HFC-236fa) and FK-5-1-12 or Novec 1230 leave no residue and are electrically non-conductive, so cleanup and downtime are low. CO2 works by cooling and removing oxygen, so it is meant for unmanned spaces like engine rooms and machine interiors. Commercial kitchens need a wet chemical system for Class F cooking oil fires.
Finally check the supporting details: cylinder capacity to suit the protected volume, whether you want a manual release or pressure switch for alarms and machine shutdown, and the approvals your client or insurer asks for. Send us your panel or machine dimensions and we will work out the system. Prices on request: call or WhatsApp +91 92440 89060.
Try "landing valve", "Apollo call point", "9 kg ABC" or a model code.
No products yet. Tap "Add to quote" on any product, then send the whole list to us in one WhatsApp message.
